do you add armour into the appearance.2da? Everything I find in there is for people, not for weapons or armour.
EDIT: oh right, well yes, apperance.2da is for people and characters.
Its baseitems for the armour and stuff, but those are only categorys
Ah. Okay. That explains a few things.
How then, do I change the environmap for the textures? Editing or making a new .txi isn't doin' the trick.
EDIT: How do I know what the name of the armour is?
How do I know what the name of the armour is?
Your going to have to find the files UTI file and i would suggest using KotOR Tool because i gives you what your looking for in text. Look for the item category (eg. "Quarter_Staff" or "Vibro_Sword") Then you can find out where it is in the baseitems.2da file
Okay, basically, this is something I've been fighting with for a while. I need to make shiny bits on the dancer's outfit unshiny. The dancer's outfit is not in the baseitems.2da, and even if it were, that still does not allow me to change the environmap, which is where the problem lies, I do believe. I tried making a .txi, however nothing happened.
what did you put in the txi?
#*****************************
# MATERIAL SPECIFIC FIELDS ***
# These fields go in the .txi file for the base texture.
# That is, do not specify these fields in the bumpmap
# or environment map .txi files - they will be ignored.
# Specify a bumpmap
#
# Default is no bumpmap.
bumpmaptexture mybumpmapname
# <--- ENVIRONMAP PART --->
# Specify an environment map for static geometry.
# Dynamic geometry uses the environment map provided on
# the model.
#
# Default is no environment map
envmaptexture myenvmapname
# Specify a blending mode for a material. This blending
# mode will override the standard mode:
#
# Options are "additive", "punchthrough", "default"
#
# Default is default.
blending default
#****************************
# TEXTURE SPECIFIC FIELDS ***
# These fields are applied to the texture being read in.
# Some are specific to different types of textures (like
# bump maps) and will be ignored if the .txi belongs to
# a texture which is not of the same type. I will try to
# document these cases.
# The default width and height of a texture in the
# absence of an image. These are usually set when you
# are using a procedural texture.
#
# Defaultfor both values is 16
defaultwidth 16
defaultheight 16
# Specify the procedural type. Only use this if a texture
# needs to be generated procedurally.
#
# Options are "water", "life", "perlin", "arturo" or "wave".
#
# Default is no procedural type.
proceduretype arturo
# Specify how the texture can be downsampled.
#
# Default is a min of 0, max of 15
downsamplemax 2
downsamplemin 0
# Specify whether or not to mipmap the texture.
#
# Default mipmap is on.
mipmap 0
# Specify whether or not to filter the texture using linear
# filtering or not. If set to 0, filtering is nearest,
# otherwise it is linear.
#
# Default filtering is linear.
filter 1
# Specify the gamma correction for this filter.
#
# Default gamma correction is 1.0
gamma 0.5
# Specify whether or not this texture is a bumpmap. If this
# flag is set, the texture module will expect to read in a
# texture which is grayscale.
#
# Default is 0
bumpmap 1
# Specify what kind of bumpmapping this bump map will do:
# specular, diffuse, or both. These values are ignored if
# this texture is not a bump map.
#
# Default: isdiffusebumpmap 0, isspecularbumpmap 1
isdiffusebumpmap 1
isspecularbumpmap 1
# Specify a scaling factor for the bumpmap height. If you
# want higher peaks and lower valleys in the bump map, set
# the value to be greater than 1. If you want a smoother bump
# map, set this value to less than 1.
#
# Default is set to 1.
bumpmapscaling 1.5
# Specify a color for specular bumpmap highlights (RGB). This
# value is modulated with the bump mapping light's color
# to produce the final highlight color.
#
# Default is (1,1,1)
specularcolor 0.5 0.5 0.8
#***********************************************
# GENERAL TEXTURE CONTROLLER SPECIFIC FIELDS ***
# These fields only apply to those textures
# which are procedural. If these values are
# specified on a non-procedural texture, they will
# be ignored.
# The following two fields specify how a procedure should be
# applied to create a final texture. The scaling factor
# indicates how much the channels of the final procedural image
# should be affected by the procedural result. The translation
# factor indicates how much to add to the scaled results for
# each channel.
#
# Default: Channelscale is all 1's, channeltranslate is all 0's.
# This creates a grayscale semitransparent image based on
# the procedure.
channelscale 4
0
0.5
0.5
0
channeltranslate 4
0.5
0.5
0.5
0.5
# The following field indicates whether or not to distort an
# image using the procedure. If this field is set to 1, it requires
# that an image be provided for this texture. Also, if this value
# is set to 1, all channelscale and channeltranslate values will
# be ignored.
#
# Default is set to 0.
distort 1
# If this value is set to 1, the texture distortion occurs in an
# angular fashion. If 0, distortion occurs in a linear fashion.
# Both are valid but can produce different distortion effects.
#
# Default is set to 0.
distortangle 0
# This value indicates how much the texture should be distorted
# (in texels). If the value is small, the original image will
# not be distorted significantly. If it is too large, the
# distortion will generate a very noisy and chaotic result.
#
# Default is set to 5.0
distortionamplitude 3.5
# This value indicates the speed of the procedure. Most procedures
# can be sped up or slowed down based on this value.
#
# Default is 1.0
speed 2.0
# The following two parameters are used for Arturo procedural textures.
# The actual arturo function is calculated using the size specified
# in these parameters, and is then upsampled to the size of the texture.
# You may be able to get better results by tinkering with these,
# although the default values work very reasonably.
#
# Default is 15 for both.
arturowidth 17
arturoheight 17
Above is information regarding the TXI file to help you, i've included everything i can...
Thanks! Where'd you find that? When I used the KotOR Tool to extract, all I got was to empty boxes with "pI" between them. On top of that, I'm not very accomplished at modding. Still fairly new.
Okay then, i assume you've solved it...
Your welcome then!
Well, I just tried it, and it didn't work, however I do believe I have to do some more digging in what you've given me. Thanks, again, though. :D
EDIT: Okay, it's still shiny. Not sure what, exactly, I'm supposed to edit.